What Is a Surge Protective Device (SPD)? A Complete Guide to Types, Working Principles, and Selection

What Is a Surge Protective Device (SPD)?

A Surge Protective Device (SPD) is an electrical protection device designed to limit transient overvoltages and divert surge currents. Under normal operating conditions, the SPD remains in a high-impedance state and has little to no effect on the electrical system. When lightning, utility switching, motor starting and stopping, or other transient events cause a sudden rise in line voltage, the SPD rapidly switches to a low-impedance conductive state. This provides a discharge path for the surge current while limiting the residual voltage reaching downstream equipment, thereby reducing the risk of insulation breakdown, electronic component damage, equipment failure, and unplanned downtime.

The design, performance testing, and practical application of SPDs must comply with relevant standards. IEC 61643-11 specifies the performance requirements and test methods for surge protective devices connected to low-voltage AC power systems, while Article 242 of NFPA 70, the National Electrical Code (NEC), addresses the application of surge protection in electrical installations in the United States. These standards provide important guidance for the testing, selection, and installation of SPDs, helping improve the safety and reliability of modern low-voltage power distribution systems.

What Is an Electrical Surge?

An electrical surge is a short-duration spike in voltage or current that travels through a power, control, or communication circuit. It typically rises very quickly and then decays over a longer period.
Although the event may last only a few microseconds, the resulting voltage can be high enough to damage insulation, electronic components, control equipment, and other sensitive loads.
IEC 60050-161 defines a surge as a transient wave that propagates along a line or circuit and is characterized by a rapid rise followed by a slower decay.

What Causes Electrical Surges?

Electrical surges are commonly associated with two major sources: lightning-related events and switching operations within the power system.
Lightning can introduce transient overvoltages through direct strikes, nearby strikes, or induced voltages in connected conductors. Switching surges may occur when motors, transformers, capacitor banks, contactors, relays, or other high-power loads are energized or disconnected.
IEC 61000-4-5 provides standardized methods for testing the immunity of electrical and electronic equipment against unidirectional surges caused by lightning effects and power-system switching transients.

COMPARISON OF LIGHTNING SURGES AND SWITCHING SURGES

Parameter	Lightning Surge	Switching Surge
Typical Waveforms	10/350 μs for direct lightning current; 8/20 μs for induced surge current; 10/700 μs for communication lines	1.2/50 μs voltage wave and 8/20 μs current wave
Occurrence Frequency	Relatively infrequent and mainly associated with thunderstorms	More frequent and may occur whenever electrical equipment is switched on or off
Energy Level	Very high energy, potentially reaching hundreds of kilojoules and causing immediate equipment damage	Generally lower energy, but repeated exposure can gradually degrade components
Recommended Protection Approach	Type 1 SPD at the main service entrance, followed by coordinated downstream surge protection	Type 2 or Type 3 SPD installed at distribution boards or close to sensitive equipment
Typical Overvoltage Range	From several kilovolts to tens of kilovolts	From several hundred volts to several kilovolts
Common Sources	Direct lightning strikes, nearby strikes, ground-potential rise, and induced lightning effects	Motors, transformers, capacitor banks, contactors, relays, and other switching devices
Typical Impact	Insulation breakdown, flashover, cable damage, fire, or immediate equipment failure	Electronic component degradation, control-system malfunction, data errors, or reduced equipment life

How does a surge protective device work?

A Surge Protective Device (SPD) works like an automated, ultra-fast electrical pressure relief valve.

Under normal grid conditions, the SPD acts as an open switch with extremely high internal resistance (impedance), preventing any power from flowing through it. However, when an overvoltage spike (caused by lightning or grid switching) enters the system, the SPD instantly reacts within nanoseconds, dropping its resistance to near-zero. This creates a safe parallel path that diverts the massive surge current away from sensitive equipment and directly into the ground.

The 3-Step Working Process

1. Normal State (High Impedance): When line voltage remains within normal operational limits, internal components maintain an impedance of several megohms. The SPD remains “invisible” to the circuit and draws virtually no leakage current.
2. Surge Event (Instantaneous Low Impedance): The moment a transient voltage exceeds the SPD’s clamping threshold (Uc), the non-linear internal elements switch from high resistance to low resistance in less than 25 nanoseconds.
3. Current Diversion & Reset (Energy Dissipation): The surge energy is safely channeled through the grounding conductor (PE). Once the transient spike subsides and the line voltage returns to normal, the internal components automatically recover to their high-impedance state, restoring standard circuit operations.

The Core Components Inside: MOV vs. GDT

The working mechanism relies on high-performance non-linear electrical components built inside the module:

• Metal Oxide Varistors (MOV): The most widely used component in Type 2 AC and DC SPDs. MOVs exhibit a sharp drop in electrical resistance as voltage increases, offering exceptional energy absorption capacities and sub-nanosecond response times.

• Gas Discharge Tubes (GDT): Commonly deployed in Type 1 spark-gap architectures or communication line protection. GDTs spark over and ionize gas when triggered, capable of discharging high lightning currents without thermal destruction.

What Are the Main Types of Surge Protective Devices?

A sudden lightning event or the switching and startup of high-power equipment in an industrial facility can generate a high-magnitude transient overvoltage within a very short period. Such surges may damage expensive controllers, servers, variable frequency drives, and other sensitive electronic equipment. In severe cases, they can even cause an entire production line to shut down. However, not every surge protective device is designed to withstand high-energy lightning currents, and not every type of SPD is suitable for installation at the same point in the electrical distribution system.

A surge protective device can be understood as the electrical system’s “airbag,” but each SPD type has a clearly defined protective role. From the first line of defense at the building’s service entrance, where high-energy surge currents are diverted, to intermediate protection in distribution panels and fine protection near sensitive equipment, Type 1, Type 2, and Type 3 SPDs operate at different levels of the protection system. In addition, Type 1+2 combined SPDs integrate the lightning-current discharge capability of a Type 1 device with the voltage-limiting performance of a Type 2 device in a single unit, making them a practical solution for service entrances and main distribution boards. Effective surge protection depends on selecting and coordinating these devices according to the system risk, installation location, and impulse withstand capability of the protected equipment.

Type 1 Surge Protective Device

Type 1 SPDs are primary surge protection devices installed on the line side of the main service entrance (between the secondary of the utility transformer and the main service disconnect).

• Primary Function: Designed to withstand high-energy transients caused by direct or nearby lightning strikes and utility grid switching before the surge reaches the main distribution panel.
• Test Standard & Waveform: Evaluated under IEC 61643 standards using the 10/350 μs impulse current waveform (Iimp), which simulates high-peak energy discharges.

Type 1+2 Surge Protective Device (Combined Type)

Type 1+2 SPDs (also classified as Class I+II) combine the high-energy impulse discharge capacity of a Type 1 device with the low voltage protection level (Up) of a Type 2 device into a single compact unit.

• Primary Function: Directly diverts high-energy direct lightning currents while simultaneously clamping low-level switching transients, providing seamless protection without requiring minimum decoupling distance between separate Type 1 and Type 2 units.
• Test Standard & Waveform: Dual-tested under IEC 61643 standards for both 10/350 μs impulse currents (Iimp) and 8/20 μs nominal/maximum discharge currents (In / Imax).

Engineering Note：
Effective surge protection relies on coordinated protection at different levels. Type 1 or Type 1+2 SPDs handle high-energy surges at the system entrance, Type 2 SPDs protect distribution circuits, and Type 3 SPDs provide fine protection for sensitive equipment.

Type 1, Type 2, Type 3, and Type 1+2 SPD: Key Differences

Feature	Type 1 SPD	Type 1+2 SPD	Type 2 SPD	Type 3 SPD
Main Function	Diverts direct lightning current	Combines lightning current discharge and surge protection	Protects against induced lightning and switching surges	Final protection for sensitive equipment
Installation Location	Service entrance	Service entrance or main distribution board	Main or sub-distribution board	Close to the protected equipment
Test Waveform	10/350 μs	10/350 μs and 8/20 μs	8/20 μs	Combination wave
Main Parameters	Iimp, Up	Iimp, In, Imax, Up	In, Imax, Up	Uoc, Up
Protection Stage	Primary protection	Primary and secondary protection	Secondary protection	Final protection

The table above provides a quick comparison of the four main SPD types. In practice, selecting the right surge protective device depends on the installation location, lightning exposure risk, system configuration, and the required level of protection. In many installations, multiple SPD types are coordinated to achieve effective surge protection throughout the electrical system.

---

How to Select the Right Surge Protective Device (SPD)

Choosing the right Surge Protective Device (SPD) involves more than simply selecting the highest discharge current rating. The system voltage, installation location, lightning exposure, grounding arrangement, and coordination between protection stages all play a critical role in determining overall surge protection performance. The following example illustrates why proper SPD selection is essential.

In late 2023, a severe thunderstorm swept through an industrial manufacturing facility in central Texas. A direct lightning strike struck the utility line less than 200 meters from the facility’s main power distribution yard. The plant did have a basic surge suppressor installed in the main low-voltage switchboard, leading plant management to believe their operations were fully protected.

Within milliseconds, the reality of incomplete surge protection unfolded:

• Massive Financial Loss: The initial high-energy impulse overwhelmed the single panel protector, sending a severe voltage transient surging through the internal distribution network.
• Catastrophic Equipment Damage: Over 15 variable frequency drives (VFDs), dozens of programmable logic controllers (PLCs), sensitive sensor arrays, and computerized CNC machining centers suffered immediate insulation breakdown and circuit board failure.
• Costly Unplanned Downtime: The entire automated production line was knocked offline for 16 days while replacement components were sourced and re-engineered, resulting in over $1.2 million in direct hardware replacement costs and lost operational productivity.

A forensic engineering analysis conducted after the incident revealed the root cause: a lack of cascaded, multi-stage surge protection. The facility relied on a single protection device at the main entrance, expecting it to absorb high-energy lightning currents while simultaneously clamping low-level voltage spikes for sensitive microelectronics downstream—a task no single device is engineered to accomplish alone.

Transient overvoltages—whether generated externally by direct or indirect lightning strikes, or internally by heavy inductive load switching—follow predictable physical paths. Protecting an industrial, commercial, or residential infrastructure requires a layered, step-down protection architecture defined by recognized international standards such as IEC 61643-01 and UL 1449.

To select the right SPD, several key factors must be considered, including the power system, operating voltage, SPD type, protection level, and installation requirements.

SPD Selection at a Glance

• Step 1: Confirm the Power System and Select Uc
• Step 2: Select the SPD Type Based on Installation Location and LPZ
• Step 3: Determine Iimp, In, and Imax
• Step 4: Check the Voltage Protection Level Up
• Step 5: Confirm the Number of Poles, Disconnection Device, Remote Signaling, and Backup Protection
• Step 6: Verify Energy Coordination Between Multiple SPDs

The following sections explain each step in more detail and show how these factors affect SPD selection.

Step 1: Confirm the Power System and Select Uc

Power System	Typical Uc Selection	Selection Note
230/400 V TN-S, TN-C-S or TT System	275 V AC for L–N protection	Common selection for standard 230 V AC distribution systems
400 V IT System	Select according to the highest possible line-to-earth voltage	The voltage to earth may increase during the first insulation fault
Solar PV DC System	Ucpv must be higher than the maximum PV array open-circuit voltage	Consider low-temperature Voc rise and system voltage, such as 600 V, 1000 V or 1500 V DC

Step 2: Select the SPD Type Based on Installation Location and LPZ

SPD types should be selected according to the installation location, lightning protection zone, lightning current risk, and the impulse withstand capability of downstream equipment. Common SPD categories for low-voltage systems include Type 1, Type 2, Type 3, and combined Type 1+2 SPDs.

Type 1 SPD – Lightning Current Protection

• Installation Location: Building service entrance, main low-voltage switchboard, and the boundary between LPZ 0 and LPZ 1.
• Main Function: Discharges high-energy lightning currents that may enter the electrical installation through the incoming power supply.
• Key Parameters: Tested with a 10/350 μs waveform. Common Iimp ratings include 12.5 kA, 25 kA, and higher values. The voltage protection level, Up, is commonly around 2.5 kV, depending on the product design.
• Typical Applications: Industrial plants, outdoor facilities, large buildings, and installations with external lightning protection systems or a high risk of direct lightning currents.

A Type 1 SPD is mainly intended to handle high lightning current energy. Additional downstream Type 2 or Type 3 protection may still be required to reduce the residual voltage reaching sensitive equipment.

Type 2 SPD – Distribution-Level Surge Protection

• Installation Location: Main distribution boards, sub-distribution boards, workshop power panels, and industrial control cabinets.
• Main Function: Protects against induced lightning surges, switching transients, and residual surge energy passing through an upstream Type 1 SPD.
• Key Parameters: Tested with an 8/20 μs waveform. Common ratings include In of 20 kA and Imax of 40–80 kA. The voltage protection level, Up, is commonly between 1.5 and 1.8 kV.
• Typical Applications: Residential buildings, commercial facilities, and general industrial power distribution systems.

Type 2 SPDs protect electrical systems against induced lightning surges, switching transients, and residual surge energy passing through an upstream Type 1 SPD.

Type 3 SPD – Final Protection for Sensitive Equipment

• Installation Location: Close to PLCs, variable frequency drives, servers, instruments, socket outlets, and other sensitive terminal equipment.
• Main Function: Further limits residual overvoltage and provides final-stage protection for sensitive electronic equipment.
• Key Parameters: Tested with a combination wave. The main parameters are Uoc and Up, although some products may also specify a nominal discharge current.
• Typical Applications: Automation systems, communication equipment, servers, measurement instruments, and other sensitive electronic loads.

Type 3 SPDs have limited energy-handling capability and should normally be coordinated with an upstream Type 1, Type 2, or Type 1+2 SPD.

Type 1+2 Combined SPD – Lightning Current and Surge Protection

• Installation Location: Building service entrances, main switchboards, solar PV AC distribution panels, compact distribution boards, and retrofit installations.
• Main Function: Combines lightning-current discharge capability and surge-voltage limitation in a single device.
• Key Parameters: Iimp, In, Imax, and Up should all be considered. Common Iimp ratings include 12.5 kA and 25 kA per pole, while In is commonly 20 kA or higher. Final values should be confirmed according to the product specifications and project requirements.
• Typical Applications: Industrial facilities, commercial buildings, solar PV systems, compact switchboards, and projects where installation space is limited.

A Type 1+2 SPD meets both Type 1 and Type 2 protection requirements in a single device. It combines high-energy lightning-current discharge capability with voltage-limiting protection.

SPD Selection Guide by Application

Application Condition	Recommended SPD Type	Typical Installation Location	Key Parameters
Building with an external lightning protection system	Type 1 or Type 1+2	Service entrance or main switchboard	Iimp, Up
General residential or commercial distribution system	Tipe 2	Main or sub-distribution board	In, Imax, Up
Sensitive electronic equipment	Type 3	Close to the protected equipment	Uoc, Up
Industrial facility with high lightning exposure	Type 1+2 with downstream Type 2 protection	Main switchboard and sub-distribution boards	Iimp, In, Up
Solar PV DC system	DC Type 1+2 or DC Type 2	PV combiner box or DC distribution board	Ucpv, Iimp or In, Up
Sensitive loads located far from the main distribution board	Additional Type 2 or Type 3	Near the downstream equipment	Up, coordination

Step 3: Determine Iimp, In, and Imax

The discharge current rating of an SPD should be selected according to the expected surge energy, installation location, lightning exposure, and SPD type. The three main current parameters are Iimp, In, and Imax.

Iimp – Impulse Discharge Current

Iimp represents the lightning impulse current that a Type 1 or Type 1+2 SPD can discharge under a 10/350 μs waveform.
It is mainly used to evaluate the SPD’s ability to withstand high-energy lightning currents at the service entrance or LPZ 0–LPZ 1 boundary.

Common In ratings include:

• 10 kA for light-duty terminal protection
• 20 kA for general residential and commercial distribution
• 30–40 kA or higher for industrial and high-exposure installations

For most main and sub-distribution boards, an In rating of 20 kA or higher is commonly selected.

Imax – Maximum Discharge Current

Imax represents the maximum 8/20 μs surge current that an SPD can discharge once or a limited number of times without failing.
Imax is normally higher than In, but it should not be used as the only selection criterion because it does not represent the SPD’s repeated operating capability.

Typical Imax ratings include:

• 20–40 kA for general distribution systems
• 40–80 kA for industrial installations
• Higher values for severe surge environments

Practical Selection Guide

Installation Condition	Recommended Parameter Focus
Building service entrance with lightning protection system	Prioritize Iimp
Main or sub-distribution board	Prioritize In and Imax
High lightning exposure industrial facility	Higher Iimp and In
Sensitive terminal equipment	Lower Up is usually more important than a very high current rating
Type 1+2 SPD	Check Iimp, In, Imax, and Up together

Step 4: Check the Voltage Protection Level Up

The voltage protection level, Up, indicates the SPD’s ability to limit surge voltage under specified test conditions. It is a declared value provided by the manufacturer and represents the protection level achieved when the SPD discharges the specified impulse current.
A lower Up generally means that less surge voltage is allowed to pass toward downstream equipment. However, Up should not be evaluated alone. It must be considered together with the system voltage, maximum continuous operating voltage Uc, discharge-current capacity, temporary overvoltage withstand capability, and the impulse withstand voltage of the protected equipment.

Compare Up with the Equipment Impulse Withstand Voltage

The selected SPD should limit the surge voltage to a level below the impulse withstand voltage of the downstream equipment.
A practical selection principle is:

• The effective protection level at the equipment should remain below the equipment’s rated impulse withstand voltage.

A sufficient safety margin should be allowed because the actual voltage reaching the equipment may be higher than the Up value stated in the datasheet.

Consider Installation Cable Length

The Up value is measured at the SPD terminals under specified laboratory conditions. In an actual installation, the inductance of the connecting conductors can add extra voltage during surge discharge.

Therefore:

• Keep the connecting conductors as short and direct as possible.
• Avoid unnecessary loops and sharp bends.
• Position the SPD close to the protected circuit.
• Install additional downstream protection when the protected equipment is far from the main SPD.

Long connecting cables can reduce the effectiveness of even a low-Up SPD. Correct installation is therefore just as important as product selection. Phoenix Contact also notes that excessively long connection conductors can create installation problems and recommends attention to cable length and layout. 

Practical Selection Focus

Protection Position	Main Selection Focus
Building service entrance	Balance Iimp and Up
Main or sub-distribution board	Check In, Imax, and Up
Sensitive electronic equipment	Select a sufficiently low Up and install the SPD close to the load
Type 1+2 combined SPD	Check Iimp, In, and Up together
Jarak jauh antara papan distribusi	Pertimbangkan SPD hilir tambahan

Engineering Note：
Jangan memilih SPD hanya berdasarkan nilai Up terendah. SPD dengan Up rendah tetapi kapasitas pelepasan tidak memadai dapat rusak oleh arus surja yang diperkirakan. Sebaliknya, SPD dengan kapasitas pelepasan tinggi tetapi Up terlalu tinggi mungkin tidak cukup melindungi peralatan sensitif.
Pemilihan akhir harus menyeimbangkan:
Uc + Up + Iimp/In/Imax + tegangan ketahanan peralatan + jarak pemasangan

Step 5: Confirm the Number of Poles, Disconnection Device, Remote Signaling, and Backup Protection

Setelah memilih jenis SPD dan peringkat listrik, pastikan perangkat sesuai dengan konfigurasi sistem dan persyaratan pemasangan. Jumlah kutub, fungsi pemutusan internal, opsi pensinyalan jarak jauh, dan perangkat pelindung cadangan semuanya memengaruhi keselamatan dan keandalan pemasangan.

Konfirmasi Jumlah Kutub

Konfigurasi kutub SPD harus sesuai dengan sistem daya, susunan penghantar, dan mode proteksi.

Power System	Konfigurasi SPD Umum
Sistem satu fasa L–N	1P+N atau 2P
Sistem tiga fasa tiga kawat	3P
Sistem tiga fasa empat kawat	3P+N atau 4P
Sistem TN-C	Proteksi antara penghantar fasa dan PEN
Sistem TN-S atau TN-C-S	Proteksi antara L–N dan N–PE, tergantung pada sirkuit yang dipilih
Sistem TT	Umumnya menggunakan sirkuit 3+1 atau 1+1
Sistem DC atau PV	Pilih konfigurasi kutub sesuai dengan tegangan sistem, polaritas, dan pengaturan pembumian

Jumlah kutub saja tidak cukup untuk menentukan kesesuaian. Sirkuit proteksi juga harus sesuai dengan pengaturan pembumian sistem dan tegangan yang mungkin muncul di antara penghantar.

Periksa Perangkat Pemutusan

Sebagian besar SPD menyertakan perangkat pemutusan termal internal yang memisahkan komponen pelindung dari sistem daya ketika mencapai akhir masa pakainya atau mengalami panas berlebih.
Perangkat pemutusan membantu mengurangi risiko:

• Pelarian termal
• Panas berlebih
• Hubung singkat
• Kebakaran yang disebabkan oleh MOV yang gagal atau komponen pelindung lainnya

SPD juga harus menyediakan indikator status yang jelas sehingga petugas pemeliharaan dapat mengidentifikasi kapan modul proteksi perlu diganti.

Tentukan Apakah Pensinyalan Jarak Jauh Diperlukan

Kontak pensinyalan jarak jauh memungkinkan status operasi SPD dipantau dari panel kontrol, sistem alarm, PLC, atau sistem manajemen gedung.

Pensinyalan jarak jauh sangat berguna di:

• Gardu tanpa pengawasan
• Lini produksi industri
• Pusat data
• Fasilitas telekomunikasi
• Pembangkit PV surya
• Sistem daya kritis

Ketika pemantauan jarak jauh diperlukan, periksa jenis kontak, susunan terminal, tegangan terukur, dan arus terukur dari kontak pensinyalan.

Pilih Perangkat Pelindung Cadangan

SPD mungkin memerlukan sekering atau pemutus sirkuit hulu untuk melindungi sirkuit jika SPD gagal atau mengalami hubung singkat internal.

Perangkat pelindung cadangan harus dipilih sesuai dengan:

• Sekering atau pemutus sirkuit cadangan maksimum yang ditentukan pabrikan
• Arus hubung singkat yang tersedia di titik pemasangan
• Peringkat arus hubung singkat SPD
• Jenis dan luas penampang penghantar penghubung
• Koordinasi dengan perangkat pelindung hulu

Jangan memilih sekring cadangan atau pemutus sirkuit hanya berdasarkan nilai arus pelepasan SPD. Ikuti tabel koordinasi dan petunjuk pemasangan dari pabrikan.

Practical Selection Guide

Selection Item	Poin Utama yang Perlu Dikonfirmasi
Number of poles	Sesuaikan penghantar fasa, penghantar netral, dan sistem pembumian
Perangkat pemutus	Konfirmasi pemutusan termal internal dan indikasi status yang terlihat
Sinyal jarak jauh	Konfirmasi apakah alarm jarak jauh atau pemantauan sistem diperlukan
Proteksi cadangan	Ikuti nilai sekring atau pemutus sirkuit yang direkomendasikan pabrikan
Modul yang dapat diganti	Periksa apakah kartrid proteksi dapat diganti tanpa mengganti alasnya
Nilai hubung singkat	Konfirmasi kesesuaian untuk arus hubung singkat prospektif

Engineering Note
SPD dengan nilai Uc, Up, dan arus pelepasan yang benar mungkin tetap tidak sesuai jika konfigurasi kutub atau proteksi cadangannya salah. Selalu verifikasi keseluruhan pengaturan pemasangan daripada memilih SPD hanya dari parameter label depannya.

Step 6: Verify Energy Coordination Between Multiple SPDs

Ketika beberapa SPD dipasang pada tingkat sistem kelistrikan yang berbeda, semuanya harus beroperasi dalam urutan yang terkoordinasi. SPD hulu harus melepaskan energi surja tertinggi, sementara SPD hilir selanjutnya mengurangi tegangan sisa sebelum mencapai peralatan sensitif.
Koordinasi energi yang tepat mencegah SPD hilir kelebihan beban sebelum perangkat hulu mengalihkan arus surja utama.

Pengaturan Proteksi Bertingkat yang Umum

Tingkat Proteksi	Tipe SPD yang Umum	Typical Installation Location	Main Function
Tahap pertama	Type 1 or Type 1+2	Service entrance or main switchboard	Melepaskan arus petir berenergi tinggi
Tahap kedua	Tipe 2	Papan distribusi cabang atau kabinet kontrol	Membatasi surja sisa dan tegangan lebih sakelar
Tahap akhir	Type 3	Dekat dengan peralatan sensitif	Selanjutnya mengurangi tegangan sisa

Periksa Jarak Antara SPD

Panjang kabel antara dua SPD memengaruhi bagaimana energi surja dibagi. Induktansi kabel penghubung dapat membantu menciptakan perbedaan tegangan yang diperlukan agar SPD hulu dan hilir beroperasi dalam urutan yang benar.
Namun, tidak ada aturan jarak tunggal yang berlaku untuk setiap kombinasi SPD. Jarak yang diperlukan bergantung pada:

• Teknologi SPD dan desain internal
• Nilai Up hulu dan hilir
• Nilai arus pelepasan
• Rute kabel dan panjang penghantar
• Data koordinasi yang diuji pabrikan

Beberapa pemasangan menggunakan panjang kabel untuk memberikan pemisahan alami. Jika jarak yang tersedia tidak mencukupi, kombinasi SPD terkoordinasi atau elemen pemisah yang ditentukan mungkin diperlukan.

Gunakan Kombinasi Terverifikasi Pabrikan

Metode paling aman adalah memilih SPD hulu dan hilir yang telah diuji dan dikonfirmasi sebagai kombinasi terkoordinasi energi oleh pabrikan.
Periksa dokumentasi pabrikan untuk:

• Kombinasi SPD hulu dan hilir yang diizinkan
• Jarak pemisahan minimum
• Apakah elemen pemisah tambahan diperlukan
• Kemampuan arus pelepasan maksimum
• Persyaratan perangkat proteksi cadangan
• Tingkat proteksi tegangan efektif pada beban

Jangan berasumsi bahwa dua SPD terkoordinasi hanya karena satu adalah Tipe 1 dan yang lainnya Tipe 2.

Pertimbangkan Jarak ke Peralatan yang Dilindungi

Ketika peralatan sensitif terletak jauh dari SPD utama, SPD hilir tambahan mungkin diperlukan. Kabel panjang dapat menangkap surja induksi baru dan juga dapat meningkatkan tegangan yang mencapai peralatan.
Untuk sirkuit distribusi yang panjang, pertimbangkan untuk memasang:

• Proteksi Tipe 2 di papan distribusi hilir
• Type 3 protection close to sensitive terminal equipment
• Additional SPDs where required by the project design or manufacturer’s instructions

Practical Coordination Checklist

Item to Verify	Selection Requirement
SPD sequence	Type 1 or Type 1+2 upstream, followed by Type 2 and Type 3 where required
Energy capacity	Upstream SPD handles the highest surge energy
Voltage limitation	Downstream SPD provides a lower effective protection level
Separation distance	Follow manufacturer-tested requirements
Cable layout	Keep all SPD connections short and direct
Product compatibility	Use verified coordinated combinations where possible
Protected-equipment distance	Add downstream protection when the load is far from the main SPD

Engineering Note
Energy coordination is not achieved simply by installing several SPDs in series. The devices must share surge energy correctly without overloading the downstream unit.
A poorly coordinated system may cause the Type 2 or Type 3 SPD to operate too early and absorb more energy than it can withstand. Final coordination should therefore follow the manufacturer’s tested combination data and installation instructions.

Where Are Surge Protective Devices Commonly Used?

Surge protective devices are widely used in residential, commercial, industrial, communication, renewable energy, transportation, and outdoor electrical systems. Their main purpose is to protect electrical and electronic equipment from transient overvoltages caused by lightning, switching operations, and power system disturbances.
The required SPD type depends on the system voltage, installation location, earthing arrangement, equipment sensitivity, and expected surge exposure.

Application	Typical Equipment Protected	Common Protection Approach
Residential buildings	Household appliances, computers, security systems, and smart home devices	Type 2 at the main distribution board; Type 1 or Type 1+2 may be required for buildings with external lightning protection
Commercial buildings	Elevators, HVAC systems, fire alarms, CCTV, servers, and building management systems	Type 1 or Type 1+2 at the service entrance, followed by Type 2 protection in downstream boards
Industrial facilities	PLCs, variable-frequency drives, sensors, automation equipment, and production lines	Coordinated Type 1, Type 2, and Type 3 protection
Data centers and communication systems	Servers, UPS systems, network equipment, communication devices, and signal lines	Power-line SPDs combined with dedicated data and signal-line protection
Solar PV systems	PV modules, combiner boxes, inverters, and AC/DC distribution circuits	DC SPDs on the PV side and AC SPDs on the inverter output side
EV charging stations	AC chargers, DC fast chargers, controllers, payment modules, and communication equipment	SPD protection at the incoming supply and charging equipment
Wind power and energy storage systems	Converters, inverters, battery management systems, control cabinets, and monitoring equipment	AC and DC SPDs selected according to the system architecture
Outdoor equipment and LED lighting	Streetlights, traffic systems, cameras, electronic signs, and outdoor control cabinets	Local SPD protection close to exposed outdoor equipment

In practice, larger or more complex systems usually require multi-stage surge protection. A high-energy SPD may be installed at the main service entrance, while additional Type 2 or Type 3 SPDs are installed closer to downstream distribution boards and sensitive equipment.

Where Should a Surge Protective Device Be Installed?

The effectiveness of a surge protective device depends not only on selecting the correct SPD type, but also on installing it at the appropriate location within the electrical system. Proper installation helps ensure that surge energy is safely diverted to earth before it reaches sensitive electrical or electronic equipment.
In most low-voltage installations, SPDs are installed in stages to provide coordinated protection from the service entrance to the final load.

Typical SPD Installation Locations

Installation Location	Recommended SPD Type	Primary Purpose
Service entrance	Type 1 or Type 1+2	Divert high-energy lightning currents entering the building
Main distribution board	Tipe 2	Protect downstream electrical circuits from switching surges and residual lightning surges
Sub-distribution board	Tipe 2	Provide additional protection for branch circuits
Dekat dengan peralatan sensitif	Type 3	Reduce the remaining surge voltage before it reaches sensitive electronic equipment
PV combiner box or DC distribution board	DC Type 1+2 or DC Type 2	Protect photovoltaic DC circuits and inverters
Control cabinets and communication systems	Type 2, Type 3, or signal-line SPDs	Protect PLCs, communication equipment, and control electronics

Installation Recommendations

To achieve the best protection performance, SPDs should be installed as close as possible to the equipment or distribution point they protect. The connecting conductors should be short and direct to minimize additional inductive voltage during surge discharge.
When the distance between the main SPD and the protected equipment is relatively long, an additional downstream SPD may be required to maintain an effective protection level.

Common SPD Installation Mistakes

Even a correctly selected surge protective device may fail to provide effective protection if it is installed incorrectly. Common installation mistakes can increase the residual voltage, reduce the SPD’s service life, or prevent the surge current from being safely diverted.The following issues should be checked during installation and commissioning.

Common Mistake	Why It Is a Problem	Recommended Practice
Installing the wrong SPD type	A Type 2 or Type 3 SPD may not be able to withstand the surge energy expected at the service entrance	Match the SPD type to the installation location and surge exposure
Selecting an incorrect Uc	A Uc value that is too low may cause premature operation or damage; a value that is too high may reduce protection effectiveness	Select Uc according to the system voltage and earthing arrangement
Using excessively long connecting conductors	Long conductors add inductive voltage during surge discharge and increase the effective protection level	Keep the connection path short, direct, and free from unnecessary loops
Poor earthing or equipotential bonding	A high-impedance earth path can prevent surge current from being discharged effectively	Ensure reliable earthing and equipotential bonding
Ignoring backup protection	An internal SPD fault may not be safely disconnected from the power system	Install the fuse or circuit breaker specified by the manufacturer
Installing only one SPD in a large system	A single SPD may not provide sufficient protection for distant distribution boards or sensitive loads	Use coordinated multi-stage protection where required
Using an incorrect pole or circuit configuration	The SPD may not protect all required conductors or may be unsuitable for the earthing system	Match the SPD circuit to the phase, neutral, polarity, and grounding arrangement
Failing to coordinate multiple SPDs	A downstream SPD may absorb more surge energy than it can withstand	Use manufacturer-verified coordinated combinations
Installing the SPD too far from the protected equipment	Long downstream cables may allow additional induced surges or increase the voltage reaching the equipment	Add downstream Type 2 or Type 3 protection when necessary
Failing to inspect or replace a failed SPD	Once the SPD reaches end of life, the circuit may no longer be protected	Check the status indicator and replace failed modules promptly

To avoid these mistakes:

• Select the SPD according to the system voltage, earthing arrangement, and installation location.
• Keep the total connection path as short and direct as practical.
• Use the correct backup protective device.
• Ensure reliable earthing and equipotential bonding.
• Verify coordination between upstream and downstream SPDs.
• Inspect the SPD status indicator during routine maintenance.

Engineering Note
The SPD itself is only one part of the surge protection system. Its actual performance also depends on conductor routing, earthing quality, backup protection, installation distance, and coordination with other SPDs.
A high-performance SPD can still provide poor protection if the installation layout is incorrect.

Frequently Asked Questions About Surge Protective Devices

Can an SPD Be Used Without a Backup Fuse or Circuit Breaker?

It depends on the SPD design and the manufacturer’s installation requirements. Some SPDs require an external backup fuse or circuit breaker, while others may include integrated overcurrent protection.
The backup protective device is used to disconnect the SPD safely if it develops an internal short circuit or reaches the end of its service life. Its rating should not be selected only according to the SPD’s discharge-current rating.
Always follow the manufacturer’s specified maximum backup fuse or circuit-breaker rating, short-circuit current requirements, and coordination instructions.

How Should a Surge Protective Device Be Maintained?

SPD maintenance mainly involves regular inspection rather than internal repair. During routine electrical maintenance, check the status indicator, remote signaling contact, terminal tightness, signs of overheating, and the condition of the backup protective device.
The SPD should also be inspected after severe thunderstorms, lightning events, major power-system faults, or repeated tripping of the upstream protective device.
Replace the SPD or plug-in protection module if:

• The status indicator shows failure.
• A remote alarm is activated.
• The enclosure is discolored, cracked, or overheated.
• The backup fuse or circuit breaker has operated because of an SPD fault.
• The manufacturer’s replacement criteria have been reached.

How Long Does a Surge Protective Device Last?

An SPD does not have a fixed service life. Its lifespan depends on the number, magnitude, and duration of the surges it absorbs, as well as system voltage, temporary overvoltages, environmental conditions, and product quality.
An SPD may remain operational for many years in a low-surge environment, but a single severe surge can significantly reduce its remaining capacity or cause immediate failure.
The status indicator and remote signaling contact should therefore be used to determine whether the SPD is still operational. Replacement should be based on actual condition and manufacturer guidance rather than a fixed number of years alone.

Do I Need Both AC and DC Surge Protection?

Both AC and DC surge protection may be required when a system contains separate AC and DC circuits. An AC SPD cannot automatically replace a DC SPD because the two devices are designed for different voltage characteristics, arc-extinguishing requirements, and system configurations.
For example, a solar PV system may require:

• A DC SPD on the PV array, combiner box, or inverter DC input.
• An AC SPD on the inverter output or AC distribution board.

Energy storage systems, EV charging systems, and industrial DC control circuits may also require separate AC and DC protection.
The selected SPD must be rated for the actual system voltage, polarity, grounding arrangement, and maximum continuous operating voltage.

Can a Damaged SPD Continue Protecting Equipment?

A damaged SPD should not be assumed to provide effective protection. Some SPDs contain an internal disconnection device that isolates the failed protection component while allowing the electrical circuit to remain energized.
In this condition, the connected equipment may continue operating, but surge protection may already be partially or completely lost.
If the status indicator shows failure or the remote alarm is activated, replace the SPD or protection module as soon as possible. Continuing to operate without replacement may leave downstream equipment unprotected.

Are SPDs Required for Solar PV Systems?

SPD requirements for solar PV systems depend on the applicable electrical standard, lightning protection design, installation risk, cable routing, and local regulations.
PV systems are particularly exposed to induced surges because modules and DC cables are usually installed outdoors and may cover a large area. SPDs are commonly installed on the DC side, AC side, or both.
Typical locations include:

• PV combiner boxes
• Inverter DC inputs
• Inverter AC outputs
• Main AC distribution boards

The required SPD type depends on whether the building has an external lightning protection system, the separation distance, the system voltage, and the lightning exposure level.
Therefore, SPDs are not selected simply because the system is photovoltaic. The need, type, and installation position should be determined by the applicable project requirements and risk assessment.

REFERENCES AND TECHNICAL SOURCES

⁠IEC 61643-11:2025 – Low-Voltage Surge Protective Devices – Requirements and Test Methods — International Electrotechnical Commission.

IEC 61643-12 – Low-Voltage Surge Protective Devices – Selection and Application Principles — International Electrotechnical Commission.

UL 1449 – Standard for Surge Protective Devices — UL Solutions.

NFPA 70 – National Electrical Code (NEC) — National Fire Protection Association.

⁠IEEE C62.41.2 – Recommended Practice on Characterization of Surges in Low-Voltage AC Power Circuits — Institute of Electrical and Electronics Engineers.

NEMA – Low Voltage Surge Protective Devices Guidance— National Electrical Manufacturers Association.

⁠IEC 62305-4 – Protection Against Lightning – Electrical and Electronic Systems Within Structures— International Electrotechnical Commission.

IEC 61643-32 – Surge Protective Devices Connected to the DC Side of Photovoltaic Installations— International Electrotechnical Commission.